An IP rating is a promise about the enclosure, not about the whole installation
When a buyer asks whether an electric heating mat is “waterproof”, the honest answer starts with two digits on a datasheet: IP65, IP67, sometimes IP68. Those letters look like a small detail next to wattage and roll width, but they are the only part of the specification that says what happens when water meets the live parts. A 200 W/m² mat with the wrong ingress rating in a walk-in shower is a problem no thermostat can fix. This article explains what the digits actually mean, how they are tested, and what a buyer should specify for a bathroom, a wet room or an apparatus floor that gets hosed down.
One point has to be made before anything else. The IP rating covers the product as it leaves the factory — the heating mat or cable jacket and, where relevant, a factory-sealed junction. It does not automatically cover the cold lead joint made on site, the thermostat on the wall, or a connector box that an electrician fills with tape. In the failures we see, water almost never gets through a tested jacket. It gets in through the part someone assembled in the room. That distinction matters more than the difference between IP65 and IP67.
Robert Chen, Senior Product Engineer, SunAura Thermal
How the IP code is built: IEC 60529 in plain language
The IP (Ingress Protection) code is defined by IEC 60529, the same international standard used across Europe, North America and most of Asia. The two digits after “IP” are independent: the first describes protection against solids, the second against water. A letter X in either position means that characteristic was not rated — IPX7 tells you nothing about dust, and IP6X tells you nothing about liquids.
First digit — solids. The scale runs from 0 (no protection) to 6. A 6 means dust-tight: vacuum is applied while the enclosure sits in a talc-like powder for up to eight hours, and no dust can reach the live parts or the mechanism inside. Every heating mat we ship for floor embedding is built to a 6, because a mat sits in tile adhesive or self-levelling compound, which is effectively a fine powder mixed with water before it sets. A 5 would keep out most dust but allows a small amount through, and “a small amount” of cement paste against a conductor is not a risk worth taking.
Second digit — liquids. This is where the confusion lives. The scale runs from 1 (dripping water) to 8 (continuous immersion), and a 9 is added for high-pressure, high-temperature steam jets. Critically, the levels are not a simple ladder where a higher number automatically includes every lower one: a 5 means protection against water jets from a 6.3 mm nozzle at 12.5 litres per minute from any direction, while a 7 means the enclosure survives 30 minutes in 1 metre of still water. A 7 says nothing about jets, which is why some industrial products are rated IP65 and IP67 together, written IP65/IP67.
For a heating mat embedded in a floor, the realistic water exposure is neither jets nor immersion. It is prolonged dampness, occasional pooling during a shower, and — in commercial kitchens and fire stations — a hose washdown. The rating that matters is therefore the one matching how the floor is actually cleaned, not the largest number on the page.

IP65 vs IP67: the two ratings buyers actually compare
Most heating mat specifications land on one of these two, and the difference is precise enough to quote from the standard.
An IP65 enclosure is dust-tight and protected against low-pressure water jets from any direction. The test uses a 6.3 mm nozzle, 12.5 litres per minute, about 3 metres distance, for at least 15 minutes per square metre of surface. Water is allowed inside only if it does no harm and does not reach live parts. For a mat buried under tile and adhesive, this is a comfortable margin: the mat never sees a jet, because the floor finish takes the water first.
An IP67 enclosure is dust-tight and survives temporary immersion: 30 minutes in fresh water at a depth of 1 metre, with the temperature within 5 K of the product’s own temperature. The test is about short-term submersion, not pressure. In practice, an IP67 heating mat is the specification for a wet room where a blocked drain or a dropped shower head could leave the floor standing in water for an hour, and for any floor that sits below ground level where backflow is possible.
Here is the misconception we correct most often: IP67 is not “waterproof forever”. It is not a rating for permanent immersion, and it does not mean the mat can be laid in a pond, a pool basin or a drainage channel. Permanent water exposure is the IP68 domain, and even an IP68 product is rated to a specific depth and time the manufacturer has agreed with the test house. A heating mat is a floor product, not a submersible appliance; anyone specifying one for a pool edge should be talking to us about the waterproofing detail around the mat, not chasing a higher digit.
| Rating | Solids test | Water test | Typical floor fit |
|---|---|---|---|
| IP65 | Dust-tight (vacuum, 8 h) | 12.5 L/min jets, 3 m, 15 min/m² | Bathrooms, kitchens, tiled floors |
| IP67 | Dust-tight | 1 m immersion, 30 min | Wet rooms, below-ground floors, hose-down areas |
| IP68 | Dust-tight | Manufacturer-defined depth and time | Not a standard floor product; ask before specifying |
| IPX4 (thermostats) | Not rated | Splashes from any direction | Wall controls in ordinary rooms |
Where the water actually gets in: the four weak points
A test house passes or fails the enclosure. Real installations fail at the joins. Four points account for nearly every water-related call we receive, and none of them is fixed by printing a higher IP rating on the box.
The cold lead termination. The heating mat ends in a cold lead, and the factory seal where the two meet is the single most important joint on the product. On our mats this is a moulded, factory-tested seal rather than a heat-shrink sleeve, because sleeves rely on the installer’s adhesive liner and age differently. If the datasheet shows the mat at IP67 but says nothing about the termination, ask the question directly: the system rating is only as good as that joint.
The junction box. Where the cold lead meets the fixed wiring, the box itself carries its own IP rating. A standard dry-wall box is IP20; a bathroom or hose-down floor needs an IP55 or IP65 box with a rated gland, and the cable entries must use the gland the box was certified with. A box rated IP65 with one cable entry drilled out and sealed with silicone is no longer the tested enclosure.
The floor probe. The sensor that tells the smart thermostat what the floor is doing sits in the floor, and its cable runs back to the control. The probe itself is sealed, but the end that plugs into the thermostat is not — that connection belongs in the wall or in a rated box, never under the tile where a future leak can find it.
Repairs and cuts. A mat that has been cut to route around a waste pipe and rejoined on site loses its factory rating at the repair unless the repair uses the manufacturer’s rated kit and is tested afterward. This is why layout drawings exist: the mat is ordered to fit the room so the floor does not need field joints.
What the test does and does not prove
An IP test is a type test. A sample of the product goes to a laboratory, is mounted as the standard requires, and is exposed to the water or dust condition described above. A pass means that construction, made from those materials, with those seals, meets the rating. It does not mean every single unit is individually immersed, and it does not predict behaviour after fifteen years of chemical exposure.
That is why a sensible buyer asks for two things alongside the rating. First, which test house issued the report and whether the report is current — a Declaration of Conformity referencing IEC 60529 is normal, and a supplier who cannot produce the underlying report when asked is a warning sign. Second, what the factory does batch to batch. In our Qingdao line, every finished mat gets a high-voltage withstand test and an insulation resistance check before it is rolled; the insulation reading is the practical gate that catches a pinched seal long before the mat reaches a floor.
It is also worth understanding what the rating leaves out. IEC 60529 says nothing about chemical resistance, so a jacket can be IP67 and still be the wrong material for a floor washed with aggressive degreasers. It says nothing about mechanical abrasion, which is why a driveway mat needs a tougher jacket than a bathroom mat even though both are dust-tight. And it says nothing about vapour: warm, damp concrete can drive moisture vapour through gaps that liquid water never reaches, which is a waterproofing-membrane problem rather than an IP problem.

How to specify the rating for each room type
The right rating follows the water exposure of the finished floor and the cleaning routine, in that order. The patterns below cover the projects we quote most often.
Ordinary bathroom, tiled. The mat sits under tile and adhesive and never sees free water. IP65 at the mat, with a factory-sealed cold lead and a rated junction box above the floor, is the standard, defensible specification. Spending more for IP67 here buys little, because the floor finish is already doing the work.
Walk-in shower and wet room. Specify an IP67 heating mat, because pooling after a blocked drain is a realistic event rather than a hypothetical. The waterproofing tanking goes in under the whole assembly, and the junction box moves out of the wet zone entirely — into the ceiling void or the adjacent room, with the cold lead routed through a rated gland.
Below-ground and basement floors. IP67 again, but the governing document is the structural waterproofing design, not the mat rating. A mat cannot compensate for a slab that admits groundwater; the drainage and membrane system has to be signed off first, and the heating is laid on top of a dry, cured structure.
Commercial kitchen and hose-down floors. This is the case where IP65 and IP67 are both relevant, plus the 9-level steam jet where washdown uses high-pressure lances. Specify the rating that matches the cleaning protocol the facility actually uses — ask the client how the floor is cleaned before choosing, because a kitchen hosed at 80 bar needs a different answer than one mopped by hand.
Controls on the wall. Thermostats carry their own ratings, and the rules differ from the mat. IPX4 is the usual minimum for a bathroom wall control, and local wiring regulations may require the control to sit outside the shower zone altogether. A high IP rating on the mat does not change where the thermostat is allowed to be mounted.
Data and evidence
The ratings and test conditions in this article are taken from IEC 60529 as it currently applies: the six-level dust scale ending in the eight-hour vacuum test, the level-5 water jet at 12.5 litres per minute through a 6.3 mm nozzle, and the level-7 immersion at 1 metre for 30 minutes. Buyers should treat those as the standard’s figures rather than as SunAura marketing claims, and any datasheet can be checked against the same clauses.
The product details reflect our own factory records. Heating mats for floor embedding are built dust-tight with moulded cold-lead seals, and every finished roll is checked with a high-voltage withstand test and an insulation resistance measurement before packing. Where a project needs a specific rating — IP65, IP67 or a combined rating for a washdown floor — the requirement is written into the order and the matching test report is supplied with the quotation rather than after it.
Certification and factory facts follow SunAura factory records: manufacturing in Qingdao, Huangdao District since 2008, ISO 9001, ISO 14001 and ISO 45001 management systems, CE and RoHS marked products, LVD and EMC tested, exported to more than 50 countries. We do not print certificate numbers in articles because audit cycles change the documents; the current Declaration of Conformity and the test report are provided on request and should be checked against the actual construction delivered.
FAQ
Is an IP67 heating mat better than an IP65 one? Not automatically. IP67 proves temporary immersion survival; IP65 proves water-jet protection. For a wet room or below-ground floor, IP67 is the right call; for an ordinary tiled bathroom, IP65 already exceeds what the mat will ever experience.
Can I lay an IP67 mat in a shower tray or pool surround? A shower floor, yes, with proper tanking and the junction outside the wet zone. A pool basin or any permanently submerged surface, no — that is not a floor-heating application and no IP67 rating is designed for continuous immersion.
Does the thermostat need the same rating as the mat? No. The thermostat is wall-mounted and carries its own rating, commonly IPX4 in a bathroom. Local wiring rules decide where it may sit; in many installations the correct answer is to mount it outside the room entirely and run the floor probe and cables to it.
How do I know the rating applies to the whole system and not just the cable? Ask for the test report and read what was tested. The report names the enclosure, the cold-lead seal and any junction components. If the supplier can only show a rating for bare cable and not for the finished mat with its termination, the system rating is an open question.
What happens if a mat is cut and rejoined on site? The factory rating is broken at that joint unless a manufacturer-rated repair kit is used and the joint is tested afterward. A drawn layout that orders the mat to the room’s dimensions is always cheaper than a field repair.
Next step
Send us the room type, the floor finish, the cleaning routine and whether the floor sits below ground. We will return the matching mat rating, the junction and gland detail, a current test report and a quotation, usually within one working day. If you are comparing suppliers, ask each one the same question — what exactly was tested, and where the cold lead is sealed — because that is the answer an IP number on a brochure cannot give you.
Robert Chen, Senior Product Engineer, SunAura Thermal
