Get a Quote

District Heating vs Electric Floor Heating in Dense Urban Retrofits

School corridor prepared for a heating retrofit

Why Dense Urban Retrofits Are a Different Problem From Anything Else

A district heating comparison usually gets written for new build. Someone draws a housing estate on greenfield land, the network is laid before the roads go down, the heat interface unit goes into a plant room that was designed for it, and the arithmetic works.

A retrofit in a dense city is not that problem. The building already exists. The street already has gas, water, telecoms and electricity in it. The plant room is a converted basement with a doorway too narrow for a packaged substation. The occupants are living there while the work happens. And the decision has to be made by someone who is comparing a connection offer from a network operator against a quote for electric floor heating, two documents that are not written in the same units and do not describe the same scope.

This article is for that buyer — the housing association asset manager, the municipal retrofit programme lead, the developer taking on a 1960s block, the consulting engineer writing the options appraisal. We will compare district heating and electric floor heating at the point where both meet the building: the heat interface unit on one side, the consumer unit on the other. We will separate capital cost from running cost from carbon intensity, because conflating them is the most common error in these appraisals. And we will be explicit about which building types each option genuinely suits, including the cases where the answer is neither.

What District Heating Actually Delivers at the Building Boundary

A district heating connection delivers energy, not heat. What arrives at the building is a pair of pipes carrying hot water at a supply temperature set by the network, and a heat interface unit that transfers that energy into the building’s own circuit. Everything downstream — the internal distribution, the emitters, the controls — remains the building’s problem.

That distinction matters for retrofit because it changes what you are buying. You are not buying a heating system. You are buying a wholesale energy supply with a fixed network temperature and a tariff, plus an obligation to maintain a heat interface unit you did not design.

Three consequences follow, and each of them has caught out a retrofit programme somewhere:

The network temperature sets your emitter requirement. A network running at 70/40 °C can feed a well-insulated floor at low temperature, but a 1960s building with 25 mm of insulation and single-glazed windows cannot run at that temperature without supplementary heat. If the network runs at 90/70 °C because it was designed for radiators, you can use that, but you are then paying for high-grade heat to do a low-grade job.

The connection capacity is a contract, not a pipe size. Network operators sell a subscribed capacity in kW, and the standing charge is usually based on it. A building that oversizes its connection to cover a cold snap pays for that capacity all year. A building that undersizes it pays penalties or loses comfort. Getting the capacity right requires a proper load calculation, not a rule of thumb from the last project.

The heat interface unit is a maintenance item in someone else’s specification.

None of this makes district heating wrong. It makes it a different kind of purchase, one where the technical decision and the commercial decision are tightly coupled and the building-side works are still yours to fund.

What Electric Floor Heating Delivers at the Same Boundary

Electric floor heating delivers heat at the point of use, from a fuel the building already has: electricity. There is no network, no connection capacity, no heat interface unit, no supply temperature constraint. What arrives at the building boundary is a supply with a known capacity — the existing service head — and what the building adds is cable, mat or film, a thermostat per zone, and the circuit protection that goes with it.

The consequences are the mirror image of the district heating list:

The building’s existing electrical capacity becomes the constraint. A 1960s block with a 60 A service head does not have the capacity to run 90 m² of floor heating at 150 W/m² on top of existing loads. The comparison is not “district heating versus electric floor heating” but “district heating versus electric floor heating plus an electrical upgrade”, and the upgrade is a real line in the budget.

There is no standing charge. You pay for what you use, at a retail tariff, with no capacity reservation. That is a genuine advantage in buildings with uncertain occupancy or intermittent use, and a genuine disadvantage in buildings where the retail tariff is high and the network tariff is not.

The maintenance item is yours, and it is small. A thermostat every ten years, a resistance test at handover, and nothing else. There is no heat interface unit to service.

Zoning is cheap and granular. A district system zones at the level the hydraulic design allows. An electric system zones at the level you can afford thermostats, which in practice is per room.

Living room prepared for a heating retrofit
A dwelling interior that has been stripped for retrofit: the floor build-up allowance and the electrical service are the two constraints that decide the emitter choice.

Capital Cost: Where the Money Actually Goes

Appraisals go wrong here more often than anywhere else, because the two options are quoted at different scopes. A district heating connection offer typically covers the connection, the heat interface unit and the network-side works, and excludes the building’s internal distribution and emitters. An electric floor heating quote often covers the heating elements and thermostats, and excludes the electrical upgrade, the floor build-up and the making-good.

To compare, both scopes have to be normalised to “heat delivered into habitable rooms”. That means adding, on the district side, the internal pipework, the emitters, the controls and the making-good. And on the electric side, the electrical capacity upgrade, the floor build-up and the same making-good.

Cost block District heating connection Electric floor heating
Network or service connection Connection charge, often distance-dependent, plus capacity reservation None, unless the service head must be upgraded
Plant room / interface Heat interface unit, metering, isolation, sometimes a new plant room Consumer unit extension, RCD or RCBO, contactor if loads are large
Internal distribution Flow and return pipework to each dwelling or zone, insulation, risers Circuits from the consumer unit, floor probes, thermostat wiring
Emitters Radiators, or a floor build-up if low-temperature operation is wanted Heating mat or film, thermal spreader, floor finish
Floor build-up Only if the emitter is a floor; otherwise not applicable Insulation board, screed or self-levelling, finish; 15–40 mm depending on method
Electrical upgrade Usually not required Often required in older blocks; may require a new supply from the network operator
Making good and access Risers, penetrations, plant room access Floor removal, skirting, door thresholds, drying time

The pattern that emerges from normalised appraisals is consistent enough to state plainly. District heating has a high fixed cost per dwelling that falls as the number of dwellings on a connection rises, and a low marginal cost per additional square metre of heated floor. Electric floor heating has a low fixed cost per dwelling and a marginal cost that scales almost linearly with heated area. That single difference explains most of the outcomes:

  • In a single dwelling with 40 m² of heated floor, electric is usually cheaper to install, sometimes by a wide margin, because there is no connection charge and no plant.
  • In a 60-dwelling block with 2,400 m² of heated floor, the district fixed cost is spread across 60 payers and the marginal cost per square metre is low. Electric, at linear marginal cost, becomes the more expensive capital option once the electrical upgrade is included.
  • In a terrace of 8 dwellings where the street already has a network main, the district connection charge is small because the main is close, and the comparison flips back.
School corridor during a heating retrofit
Public buildings in dense areas are often the first candidates for a retrofit options appraisal, because the access and consent constraints are visible before any money is spent.

Running Cost: the Tariff Structure Decides, Not the Efficiency

Buyers frequently compare running costs by comparing efficiencies. That is the wrong comparison in a retrofit, because the two options are on different tariff structures with different fixed components, and the fixed component often dominates the annual bill.

District heating tariffs typically have a fixed capacity charge, a variable energy charge per kWh, and sometimes a separate return-temperature penalty for customers who run their circuits too cool. Electric heating is on a retail tariff with a standing charge, a unit rate, and — increasingly — a time-of-use structure that changes the price by hour.

The comparison therefore depends on four variables that are rarely all known at appraisal stage: the subscribed capacity, the network’s fixed charge per kW, the retail tariff’s time-of-use spread, and the building’s actual annual heat demand after retrofit insulation.

Two practical observations from appraisals we have been involved in:

Low-occupancy and intermittent-use buildings favour electric. A building with a fixed capacity charge pays it whether or not anyone is home. A time-of-use electric tariff with a heat-storage or preheat strategy can move consumption into the cheap hours, and a building that is empty half the week can simply not heat.

High-demand, continuously occupied buildings favour district. Where annual demand is predictable and high, the district variable rate is usually below the retail electricity rate per delivered kWh, and the fixed charge is diluted. This is particularly true where the network runs on waste heat or a heat pump with a low-cost power contract.

Carbon Intensity: the Number That Moves

The carbon comparison is the one most likely to be decided on stale figures. Electric heating’s carbon intensity is the grid’s carbon intensity, and the grid is decarbonising in every European market. District heating’s carbon intensity is the network’s fuel mix, and that is decarbonising more slowly in networks built around gas CHP, and faster in networks adding waste heat, geothermal or large heat pumps.

The practical implication is that an appraisal using today’s grid factor will understate electric heating’s future position, and an appraisal using today’s network factor will overstate district heating’s future position unless the network has a published decarbonisation plan with dated milestones. Ask for that plan. A network without one is a network whose carbon case is frozen at the date of the appraisal.

There is a second-order effect that matters in dense urban retrofit: electrical infrastructure has its own carbon cost, and so does a district network. A connection that requires a new substation and a service upgrade carries embodied carbon that a low-temperature electric retrofit in an existing service may avoid entirely. That is rarely counted in a retrofit options appraisal and it should be.

Retrofitting a Building That Already Has a District Connection

This is the case where the answer is usually not a choice at all. If the building is already connected, the connection charge is sunk, the heat interface unit exists, and the marginal decision is about the emitters inside the dwelling, not about the energy source.

In that situation, electric floor heating is often being installed as a supplementary system in wet rooms, extensions and rooms the existing distribution does not reach well, rather than as a replacement for the network supply. That is a legitimate and common configuration, and it changes the specification: the electric system is sized for the room it serves, not for the whole dwelling, and the circuit protection must be coordinated with the existing installation rather than designed as a standalone.

The genuinely difficult case is a building connected to a network running at high temperature, where the landlord wants to lower the flow temperature to improve network efficiency but the building’s emitters cannot run cool. There, a low-temperature electric floor in the worst-performing rooms can allow the network flow temperature to drop for the rest of the building, which is a system-level benefit that never appears in a room-level payback calculation.

Marking out a heating element position before installation
Marking out before installation: the measured position, the circuit route and the protection device have to be agreed before the finish goes back down.

Retrofitting a Building That Does Not

Here the comparison is genuinely open, and the deciding factors are usually not the ones in the marketing material. In order of how often they decide the outcome:

Whether the street has a network main within reach. Distance to the main drives the connection charge more than anything else. A building 400 m from a main and a building 20 m from a main are different propositions even if they are identical buildings.

Whether the electrical service can carry the load. A service upgrade is a multi-party, multi-month process. If the building needs one, the electric option’s timeline advantage disappears.

Whether the floor can be opened. A solid floor in a listed building, a floating finish that cannot be disturbed, or a floor with a wedding-cake of existing finishes all raise the cost of any floor-based emitter, electric or hydronic.

Who carries the maintenance obligation for twenty years. A housing association that already runs a district connection has the capability to run another. An organisation that has never maintained a heat interface unit is buying a new capability, and that cost is real even when it does not appear in the capital budget.

Selection Framework

The table below is the one we use in a first-pass appraisal. It is a screening tool, not a design. Every row still needs a load calculation and a normalised cost comparison before it becomes a decision.

Building situation Usually favours Why What would change the answer
Single dwelling, 30–50 m² heated floor, no network main nearby Electric floor heating No connection charge; fixed cost is low; electrical service usually adequate A service upgrade requirement, or a network main already at the boundary
Single dwelling with an existing district connection Keep the connection; electric for wet rooms and extensions Connection charge is sunk; the marginal decision is about emitters, not fuel A network flow temperature that cannot serve the building’s emitters
Block of 40–100 dwellings, network main in the street District heating Fixed cost spread across many payers; low marginal cost per m²; maintenance capability exists at portfolio level High network fixed charge, or a low-demand building stock after deep retrofit
Block of 40–100 dwellings, no main within 300 m Usually electric, with a serious look at the service capacity Connection charge and street works dominate; electric fixed cost is per dwelling A municipal programme that subsidises the connection charge
Listed or solid-floor building Neither floor option without a specialist assessment; often high-temperature electric or a hybrid Floor opening cost and consent risk are the binding constraints A floor finish that can be lifted and relaid, or a wall/ceiling emitter route
Intermittently occupied or seasonal building Electric No capacity standing charge; zone control per room; heat only when occupied A retail tariff with a very high peak rate and no storage
Building with waste-heat or heat-pump network at low flow temperature District, with a low-temperature floor inside Low-grade energy doing a low-grade job is the efficient pairing Building emitters that cannot run below 55 °C without supplementary heat

What to Ask Before You Commit

Both options are sold with documents that omit the questions that decide the outcome. This is the list we would want answered before signing either.

# Question Applies to
1 What is the network’s design flow and return temperature at the building boundary, and does it vary by season? District
2 What subscribed capacity am I contracting, what is the fixed charge per kW, and what happens if I exceed it? District
3 Is there a return-temperature penalty, and how is it measured? District
4 Does the network have a published decarbonisation plan with dated milestones? District
5 Who owns, maintains and replaces the heat interface unit, and on what schedule? District
6 What is the existing service head capacity, and what does an upgrade cost and take in this supply area? Electric
7 What is the floor build-up budget — how many millimetres can be added without touching doors, skirting and thresholds? Electric
8 What is the tariff structure, including time-of-use windows and any capacity component? Electric
9 What is the post-retrofit heat demand per dwelling, calculated rather than assumed? Both
10 What is the making-good scope, and who pays for finishes damaged by access? Both

Four Mistakes We See in These Appraisals

1. Comparing a connection offer against an element quote. The two documents cover different scopes, so the cheaper number is usually the one with less in it. Normalise both to heat delivered into habitable rooms before comparing anything.

2. Using efficiency ratios as a proxy for running cost. A seasonal performance figure says nothing about the fixed charge, and the fixed charge is often the larger number in a low-demand building.

3. Assuming the electrical service is adequate because the building has electric showers. Showers are intermittent. Floor heating is continuous for hours. The load profiles are not comparable, and diversity assumptions that work for showers understate a heating load.

4. Freezing the carbon comparison at the appraisal date. Both the grid and the network are changing. An appraisal that does not state which year’s factors it used, and how they move, is not auditable five years later when the decision is reviewed.

Data and Evidence

SunAura Thermal has manufactured flexible heating elements in Qingdao’s Huangdao district since 2008, with ISO 9001, ISO 14001 and ISO 45001 certification covering quality, environmental and occupational safety management at that plant. European-market products ship with CE marking supported by Low Voltage Directive and EMC documentation, and RoHS material compliance declarations. We export to more than 50 countries, and a growing share of our volume goes to retrofit programmes where the electric option is being compared against a network connection rather than against another electric product.

The technical framing in this article draws on three source families. District heating network temperatures, connection practice and tariff structures follow the guidance published by Euroheat & Power and the metering and billing requirements of the EU Energy Efficiency Directive as transposed nationally. Building heat demand and emitter temperature requirements follow EN 12831 for load calculation and the low-temperature operation guidance in EN 442 for radiators and EN 1264 for water-based floor heating. Electrical load, diversity and service capacity follow IEC 60364 and the national wiring rules that implement it.

Every heating element we ship is insulation-resistance and high-voltage tested before packing, with the test record travelling with the consignment so an installer can establish a baseline before the floor is closed. For retrofit programmes comparing options, that record is the piece of evidence that makes an electric option auditable at handover in the same way a district connection’s commissioning data is.

FAQ

Is district heating always lower carbon than electric floor heating? No. It depends on the network’s fuel mix and on the grid’s carbon intensity in the same year. A gas-CHP network compared against a low-carbon grid can be the higher-carbon option, and that gap widens as the grid decarbonises.

Can electric floor heating work in a building with a 60 A service? Sometimes, if the heated area is small and the existing load is light, but it needs a real load calculation with diversity applied to the heating circuits, not an assumption. Above roughly 40 m² of heated floor at 150 W/m² in a dwelling with normal loads, the service becomes the constraint.

Does a district connection remove the need for floor heating? No. It supplies energy at the boundary. The emitters inside the dwelling are still a separate decision, and a low-temperature network is best served by a low-temperature emitter such as a floor.

Which option is faster to deliver in a dense urban retrofit? Usually electric, because there are no street works and no connection queue, unless the building needs a service upgrade. Street works in a dense area carry their own consent and traffic timeline that rarely appears in the headline programme.

What if the building already has radiators from a previous system? Then the district option can reuse them if the network temperature suits, which changes the capital comparison substantially. The electric option cannot reuse them and must fund a floor build-up.

How should a programme compare options across 40 buildings? Normalise each to cost per kWh delivered per dwelling per year, including fixed charges, and state the carbon factors and the year they apply to. A per-square-metre comparison across buildings of different density is not a comparison.

Next Step

If you are writing an options appraisal for a retrofit programme and want the electric side costed at the same scope as the connection offer, send us the dwelling count, heated area per dwelling, existing service capacity and floor build-up allowance. We will return an element selection, a circuit and protection layout, and the documentation your programme board will want at the point the decision is minuted.

For the emitter comparison inside the building, our electric versus hydronic floor heating comparison covers the running-cost arithmetic, and the electric heating mat range lists the sizes and wattages that fit a standard retrofit floor build-up. Programmes procuring at volume can request the load and circuit schedule as part of the quotation so the electrical case and the element specification are released together.

Ethan Sun, Founder & CEO, SunAura Thermal