Overview
The SunAura graphene wall heating film is a thin, flexible printed-heater sheet designed to be fixed directly to an interior wall and turned into a silent radiant heat surface. It is not another fan heater, oil column or convector that stacks hot air near the ceiling: this film converts more than 99 % of the electricity it draws into far-infrared energy that radiates from the wall plane, warming the wall mass, the furniture and the people in the room. The film body itself is ultra-thin and flexible, so when it is switched off the room barely notices it is there, and when it is switched on the wall quietly becomes the radiator.
Inside the sheet, printed graphene-carbon resistive stripes run across a laminated film with a silver reflective insulation backing. When current passes through the stripes, they heat up almost instantly; the reflective backing sends the radiated energy back into the room instead of wasting it into the wall behind. The in-line thermostat supplied with the film gives two heat settings, High and Low, so the room can run at economy level overnight and boost up when occupied. Because the element is fully shielded, the film emits no electromagnetic radiation — an important point for bedrooms, nurseries and long office hours.
For B2B buyers, this product is built on the same production platform as SunAura’s wider graphene home heating range. Our Qingdao factory has operated since 2008, runs six automated production lines, holds a monthly output of roughly 500,000 m² of graphene heating film, and ships to more than 50 countries under ISO 9001 quality and ISO 14001 environmental management, with CE and RoHS certification on the product line. Standard wall film is plug-and-play; Standard stock ships as 50 cm-wide strips from 0.3 to 4 m long, on 220 V plug-and-play operation; wider panels are assembled from multiple 50 cm strips. OEM and ODM buyers can discuss cut lengths, plug standards, controller styles and zone-thermostat pairing for their market.

How the Graphene Wall Heater Works
Convection heaters work by warming air, which then rises and circulates. That strategy costs energy: heat collects at ceiling level, rooms feel warm near the heater and cold near the floor, and every door opening dumps a wave of heated air out of the room. A radiant wall film works the other way around. The graphene element reaches operating surface temperature in roughly one minute, as our own demo footage shows, and radiates far-infrared energy toward the opposite wall and the occupants in the room. Those surfaces and bodies absorb the energy and re-emit it slowly, so the room stays evenly warm without drafts, without fan noise and without blowing dust around.
The wall itself acts as a low-temperature storage panel. Once the wall surface is warm, it keeps radiating for a short period even after the film switches off — the kind of gentle thermal mass effect that buyers notice as “warm walls, not just warm air”. For retrofit rooms, rented flats, offices and small hospitality spaces, this is a practical advantage: no radiator occupies floor space, no wet trades are needed, and the heater can sit under a window (where cold downdraft is worst), above a bed, behind a sofa line or over a bathroom vanity wall.
Key Specifications
| Parameter | Value |
|---|---|
| Heating element | Printed graphene-carbon far-infrared resistive film |
| Heating principle | Far-infrared radiant heating; electric-to-thermal conversion > 99 % |
| Radiation shielding | Fully shielded construction — no electromagnetic radiation emission |
| Form factor | Ultra-thin, flexible sheet; wall-mounted; zero floor space |
| Backing layer | Silver reflective insulation backing (reflects heat into the room) |
| Supply control | Plug-and-play in-line thermostat with two heat settings (High / Low) |
| Warm-up time | Approx. 1 minute to operating surface temperature (product demo footage) |
| Measured surface temperature | Approx. 67.7 °C read by an infrared thermometer gun (factory demo video) |
| Suitable wall surfaces | Interior drywall, plaster, ceramic tile, wood paneling and wallpaper |
| Mounting method | Tape positioning + adhesive fixing; factory-printed fixing-hole strips allow screw fixing |
| Brand | SunAura Thermal |
| Rated voltage | 220 V |
| Rated power per panel | 125–1000 W across the size range (power density 500 W/m²). Per panel: 50×50 cm = 125 W, 50×100 = 250 W, 50×150 = 375 W, 50×200 = 500 W, 50×250 = 625 W, 50×300 = 750 W, 50×400 = 1000 W |
| Standard panel sizes (W × L) | 30×50, 50×50, 50×100, 50×150, 50×200, 50×250, 50×300, 50×400 cm. Standard film width is 50 cm; the 30 cm-wide version is only available on the 30×50 cm panel |
| Working temperature | 45–55 °C (thermostat-controlled) |
| Typical surface temperature | Approx. 60 °C per the factory configuration guide (uncovered surface; varies with ambient conditions) |
| Surface temperature uniformity | ≤ 3 °C across the panel (per factory spec) |
| Total film thickness | Available on request (factory datasheet) |
| Model / SKU | Wall-mounted high-temperature film series (50 cm-wide strips; factory code: graphene electric heating film) |
| Supply cord length | Plug-ready lead with in-line thermostat; exact length on request |
| Supply notes | Standard film width 50 cm; panels wider than 50 cm ship as multiple 50 cm strips (a 1 m-wide order ships as two 0.5 m strips). All panels include the reflective insulation backing; versions without the in-line thermostat ship plug-ready |
| Installation environment | Designed for interior wall installation; not intended for outdoor or wash-down exposure |
| Certifications | CE, RoHS; manufactured under ISO 9001 and ISO 14001 management systems |
| Warranty (as shown in product demo) | Controller 1 year / film body 3 years; backed by SunAura company-level 15-year warranty support for registered B2B partners |
| Origin & supply | Qingdao, China; 6 automated production lines; ~500,000 m² monthly capacity; exported to 50+ countries |
Film thickness and exact lead length are published in the factory datasheet on request. Tell us your target plug standard and room sizes, and we will quote the matching strip length and power configuration.
Panel Selection Guide
The film ships as 50 cm-wide strips cut to length. Use this table as a starting point: “indicative main coverage” assumes the wall film is the primary heat source in a reasonably insulated room; “indicative auxiliary coverage” assumes it supplements an existing heater or radiator.
| Panel size | Rated power (per factory SKU list) | Indicative main coverage | Indicative auxiliary coverage |
|---|---|---|---|
| 30×50 cm | 60 W (per factory configuration guide) | 0.3–0.5 m² | 0.4–0.7 m² |
| 50×50 cm | 125 W | 0.7–1 m² | 0.9–1.2 m² |
| 50×100 cm | 250 W | 3–5 m² | 5–7 m² |
| 50×150 cm | 375 W | 4–6 m² | 6–8 m² |
| 50×200 cm | 500 W | 5–7 m² | 7–9 m² |
| 50×300 cm | 750 W | 7–10 m² | 8–12 m² |
| 50×400 cm | 1000 W | 10–15 m² | 12–16 m² |
Coverage figures are indicative — actual results depend on regional ambient temperature and room insulation. Confirm sizing with our engineers before ordering. The 30×50 cm panel is the narrow 30 cm-wide version and is rated 60 W per the factory configuration guide; all 50 cm-wide strips follow the factory SKU list at 500 W/m² density.
Key Features & Benefits
- Far-infrared radiant comfort — warms walls, furniture and people directly instead of stirring up dust with forced air.
- Over 99 % electric-to-heat efficiency — nearly every watt drawn becomes radiated heat; nothing is lost to fan motors or chimney-like convection stacks.
- Zero floor footprint — the film lives on the wall; no radiator, no oil column, no storage heater eating into room layout.
- About one minute to warmth — fast surface warm-up on the demo bench, with two High/Low settings for boost and economy.
- Plug-and-play in-line thermostat — standard rooms do not need an electrician; plug into a wall socket and select High or Low.
- Flexible and corner-friendly — the sheet follows inside corners and uneven walls, with no rigid panel to bend around.
- Silent and fanless — no blower noise, useful for bedrooms, offices, libraries and hospitality.
- Shielded, no electromagnetic radiation — safe choice for nurseries, children’s rooms and long office workdays.
- Simple, documented fixing — tape to position, adhesive to hold, and screw fixing on the printed reinforcing strips if the wall requires it.
- Smart-thermostat ready — pair the film with SunAura room thermostats for scheduled, zoned control in multi-room projects.
Typical Applications
- Bedrooms and nurseries — low-temperature radiant warmth above the headboard or across the bed wall; silent, no fan noise at night.
- Living rooms and lounges — mounted flush below wall art or behind a sofa line; invisible when off, warm when on.
- Bathroom walls — marble or tiled walls above the toilet give gentle morning warmth without a dedicated heated towel rail circuit.
- Dining rooms, tea shops and small restaurants — warm walls keep seated customers comfortable while the floor stays clear for chairs and service.
- Home offices and studies — under a window or behind the desk to chase off under-desk cold during long workdays.
- Below windows — directly counteracts cold downdraft from glass, the single biggest cold-spot in most rooms.
- Rental and retrofit projects — no wet trades, no demolition; a weekend upgrade that tenants and landlords both accept.
- Showrooms, galleries and retail walls — discreet radiant heat that does not compete with the interior design.
Customer Installations — Real Wall-Heating Projects
The photos below are genuine customer and installer shots of SunAura graphene wall heating film, grouped by room type. They show where buyers actually put the film — above headboards, below windows, on marble tile, around inside corners and behind desks — and what problem each installation solves. All images are on walls, indoors, exactly as the product is designed to be used.
Bedrooms & Nurseries
Bedrooms are where buyers feel the difference most: warm walls instead of a noisy fan, and a heater that never reaches for floor space. The film runs along the bed wall above the headboard, giving a soft radiant backdrop across the whole bed.






Living Rooms & Lounges
In living rooms buyers care about furniture first: the heater must not steal sofa space or clash with artwork. Installations sit mid-wall below pictures or over damask wallpaper, blending into the interior.



Dining Rooms, Tea Shops & Small Hospitality
Seated customers feel coldest at their backs. A warm wall behind the dining chairs solves that without taking floor space that service staff need.


Bathroom Walls
The film is intended for interior wall installation; a marble-tiled wall above the toilet is a typical cold-morning spot that buyers choose for gentle radiant warmth.

Home Offices & Studies
Long workdays have two pain points: a cold window behind the shoulders and a cold floor under the desk. The film addresses both as a wall line.



Under-Window Walls and Corners
Below windows and around inside corners are where convection radiators usually struggle. The flexible film follows both.



Product Build, Wiring & Installation Detail
These close-ups show what buyers and installers actually receive: the reflective backing, the in-line thermostat, the printed safety strips, and the tape-and-adhesive fixing method used on real walls.







Video Gallery
Four short clips from our product and installation team: installation method, measured surface temperature, the in-line thermostat and warranty, and the value pitch for buyers worried about winter heating bills. All footage is real — no CGI heaters.
Step-by-step wall mounting, followed by an infrared thermometer gun reading about 67.7 °C on the film surface — showing how quickly the graphene film heats once pressed to the wall.
From floor-laid film to a finished panelled living room — demonstrates the actual surface temperature and the comfortable radiant feel buyers report in-use.
Highlights the ultra-thin flexible body, the in-line High/Low/Off switch, and the product-demo warranty of 1 year on the controller and 3 years on the film body; about one minute to heat up.
A short talk through the buyer’s objection: high winter heating costs, zero floor-space footprint, and the simple plug-in thermostat operation.
Installation Guide
The wall film is designed for DIY-friendly retrofit on ordinary interior walls. Our installers follow the same sequence on every job; the key is to keep the film flat and the front face clear.
- 1. Prepare the wall. Wipe the wall surface clean and dry. Suitable bases include painted drywall, plaster, ceramic tile, wood paneling and wallpaper. Choose a spot with no furniture blocking the front face — the heat must radiate outward.
- 2. Position the film. Hold the film against the wall at your chosen height (typically above a headboard, below a window, or behind a sofa line) and secure it temporarily with tape strips along the top and bottom edges, as seen in our installation photos.
- 3. Fix permanently. Press the film flat onto the adhesive backing so it makes full contact with the wall. If the wall is uneven, plasterboard or high-traffic, use the factory-printed fixing-hole strips along the silver foil border for screws — the print marks exactly where drilling is allowed.
- 4. Connect the thermostat. Route the power cord to the nearest wall socket. The in-line thermostat with High / Low / Off plugs directly into the socket — no fixed wiring needed for standard rooms.
- 5. Test and commission. Switch to High, wait about one minute, and check the film is heating evenly across all stripes. Keep the radiating front face unobstructed, then switch to Low for overnight or economy operation.
For fixed-wiring projects, multi-room zoning or commercial hospitality fit-outs, our engineering team can pair the film with SunAura room thermostats and supply a wiring schematic for your electrician.
Safety & Compliance
Safety instructions are printed on the film itself, in both the foil border and the corner warning label, so end users always see them. The rules are simple:
- Must be wall-mounted. Never run the film on a floor, on bedding, or inside a cabinet.
- Keep the radiating front face clear. Do not cover the film with cloth, cushions, shelves or stored items.
- High-temperature surface — never cover. This is a wall-mounted high-temperature film: the uncovered surface typically runs at 50–70 °C and varies with ambient conditions. If the film is covered by clothing, bedding, curtains or any insulating material, the trapped heat can drive the surface temperature above 100 °C rapidly. Never cover the heating surface with any object or insulation.
- Fixing holes only on the printed strips. Drill where the marking indicates; never drill through a heating stripe.
- Disconnect when unattended. Unplug or switch off the in-line controller when leaving the room for long periods.
On the compliance side, the wall heating film line carries CE and RoHS certification, and our Qingdao factory operates under ISO 9001 quality and ISO 14001 environmental management systems. The film is shielded so it emits no electromagnetic radiation. For the Japanese market, SunAura sells in compliance with local regulations on a project basis: we discuss certification requirements (including PSE-related matters) per order and confirm the required documentation before shipment, rather than making blanket claims.
Warranty: the in-box product warranty demonstrated in our product video covers the controller for 1 year and the film body for 3 years. Separately, SunAura maintains a company-level 15-year warranty support framework for registered B2B partners, covering manufacturing-defect handling and long-term parts support across our graphene home heating range.
Frequently Asked Questions
How much electricity does the graphene wall heating film actually use?
The film converts more than 99 % of drawn electricity into radiated heat, so there is almost no parasitic loss from fan motors or air circulation. The exact wattage per panel is listed in the specification sheet (pending factory confirmation) and depends on panel size. Because radiant heating warms people and walls rather than just air, rooms typically feel comfortable at a lower air temperature than a convection-heated room. Send us your room dimensions, insulation level and target temperature, and we will estimate the panel configuration and running cost range.
Is the wall heating film safe for bedrooms and children’s rooms?
Yes. The film is fully shielded and emits no electromagnetic radiation; it is silent, fanless and runs at a typical uncovered surface temperature of about 60 °C (measuring about 67.7 °C in our demo footage). It is warm to the touch while uncovered on an open wall, but only because the front face must stay clear — covered by bedding or any insulating material it would overheat, which is why nurseries should use the Low setting on an open wall position. The printed safety rules require wall mounting and a clear front face, and the film carries CE and RoHS certification.
Can I install it myself, or do I need an electrician?
Standard retrofit rooms are plug-and-play: tape the film into position, press it flat, screw the fixing strips if needed, then plug the in-line thermostat into a wall socket. No electrician required. For fixed-wiring, multi-zone or commercial projects, we can supply a schematic for your licensed electrician.
What surface temperature does the film reach?
In our product demo footage, an infrared thermometer gun measured about 67.7 °C on the film surface during testing, and the room-level demo recorded about 50.9 °C in a finished-living-room test. The two High/Low settings let you choose boost or economy. Always keep the front radiating face unobstructed for consistent temperature.
How long does the film last, and what is the warranty?
The product-demo warranty covers the controller for 1 year and the film body for 3 years. Registered B2B partners are additionally covered by SunAura’s company-level 15-year warranty support framework, which handles manufacturing-defect claims and long-term parts supply across our graphene home heating range. Properly wall-mounted and used per the printed safety instructions, the printed graphene element has a long service life — that is the same production platform we have shipped in over 50 countries since 2008.
Which rooms is the wall film best for?
Bedrooms, living rooms, bathroom walls above the toilet, dining rooms and tea shops, home offices, and walls directly below windows — anywhere cold downdraft or under-desk cold is the complaint. It is designed for interior wall installation; it is not intended for outdoor use or wash-down exposure.
Can I cover the film with clothes, a blanket or furniture?
No. The uncovered surface typically runs at 50–70 °C, but if it is covered by clothing, bedding, curtains, cushions or any insulating material, the trapped heat can drive the surface above 100 °C rapidly. This is exactly why the printed safety rules require the radiating front face to stay clear. Keep the full face of the film open to the room, never hang anything on it, and never run it behind bedding or a cabinet.
Can it be paired with a smart thermostat or zoned control?
Yes. The in-line High/Low thermostat is the standard entry solution, but for multi-room projects the film can be paired with SunAura room thermostats for scheduled, zoned, app-controlled heating. Tell us your number of rooms and preferred controller brand, and we will quote the matching setup.
Do you supply the Japanese market, and what about PSE?
SunAura sells compliantly per local regulations. We currently hold CE, RoHS, ISO 9001 and ISO 14001 certification; for the Japanese market we discuss PSE-related documentation on a per-order basis and confirm the required compliance steps before shipment. Send us your project size and we will map the paperwork path.
Related Graphene Heating Products
This wall film is one member of our graphene home heating series. Buyers often pair it with the following: browse the full range in our product center.
- Graphene infrared heating painting — a framed wall-art radiant panel for rooms where decor matters more than a slim film.
- Graphene far-infrared space heater — a fanless room heater for rooms that need portable, higher-wattage radiant heat.
- Custom encapsulated heating film — factory-sealed film for damp-room and custom-length orders.
- Flexible heating film rolls — wide film rolls for blankets, mats and mattress projects.
Procurement, OEM & Wholesale Terms
Every figure below is the factory specification of this wall film, not a marketing range. If you are specifying for a distributor, a contractor or an OEM programme, this section answers the four questions your purchasing team asks first: compliance, parameters, minimum order and how the price is built.
Compliance
CE · RoHS
ISO 9001 & ISO 14001 factory systems
Minimum order
Flexible
Single panels and trade samples available
Production lead time
25–35 days
Sea freight, after deposit and sample approval
Quotation
Within 24 h
Price, MOQ, freight and lead time in one reply
Technical parameters your specification needs
| Parameter | Value |
|---|---|
| Rated voltage | 220 V (other voltages on request) |
| Power density | 500 W/m² across the standard range |
| Panel output | 125 W (30×50 cm) up to 1,000 W (50×400 cm) |
| Working temperature | 45–55 °C thermostat-controlled; uncovered surface ≈60 °C |
| Surface uniformity | ≤3 °C across the panel |
| Electric-to-thermal conversion | >99 %, far-infrared radiant output |
See the certification documents — CE, RoHS, ISO 9001, ISO 14001.
MOQ, Incoterms and what we need in order to quote
Installers and distributors can start with single panels or a mixed trade sample. A sample order is quoted at sample quantity, not at production minimums.
Minimum quantity depends on film width (standard 50 cm), power density, panel mix and destination. We confirm the exact MOQ in writing with the quotation rather than publishing a number that changes with every configuration.
EXW Qingdao or FOB. Freight, insurance and duty are quoted separately so the unit price stays comparable between suppliers.
25–35 days for sea freight after deposit and approved sample; express air for samples and urgent pilot runs.
How the price is built — volume bands
| Order stage | Typical quantity (guide) | What the quotation covers |
|---|---|---|
| Sample / evaluation | 1–5 panels or 1–5 m² | Unit sample price, packaging, express freight |
| Trial order | 20–100 m² | Per-m² or per-panel price, MOQ confirmation, freight options |
| Wholesale / distributor | 100–1,000 m² | Volume price break, mixed-size pallet loading, private-label packaging |
| Project & OEM | 1,000 m²+ or annual programme | Programme pricing, label/tooling setup, scheduled releases |
Prices are quoted per square metre or per panel and depend on film width, power density, panel mix and Incoterm. We do not publish one list price that would be wrong for your configuration: send the band you fall into and the applicable price break comes back in the 24-hour reply.
OEM / ODM — four steps from specification to shipment
Send room layout, target voltage and plug standard, panel sizes and annual volume. We return a configuration sheet with wattage per panel and a bill of materials.
Pre-production sample with your label artwork and packaging. You approve surface temperature, uniformity and plug type before tooling is committed.
Small production batch that validates packing, labelling and logistics, with a QC report and photo record.
Scheduled releases against the approved sample, per-batch QC, and export documentation including the CE/RoHS declaration, packing list and invoice.
Send a bulk inquiry — reply within 24 hours
Include quantity (m² or number of panels), panel sizes, voltage and plug standard, destination port, and whether you need private-label packaging. Our engineers size the load room by room and return price, MOQ and lead time together.
Request bulk pricingWhatsApp an engineerRequest a Quote for Graphene Wall Heating Film
Tell us your target voltage, plug standard, panel sizes and number of rooms, and our engineering team will come back with configuration, pricing and lead time from Qingdao. OEM and ODM orders welcome.
Request Wholesale Price
WhatsApp an Engineer
