Get a Quote
Graphene Home Heating · SunAura Factory Direct

Graphene Wall Heating Film — Far-Infrared Wall Heater

Model: XGF-WALLFILM CE & RoHS Factory since 2008 OEM / ODM Welcome

Ultra-thin graphene far-infrared wall film — 99% conversion, plug-and-play thermostat, zero floor space. CE/RoHS, factory Qingdao since 2008.

Overview

The SunAura graphene wall heating film is a thin, flexible printed-heater sheet designed to be fixed directly to an interior wall and turned into a silent radiant heat surface. It is not another fan heater, oil column or convector that stacks hot air near the ceiling: this film converts more than 99 % of the electricity it draws into far-infrared energy that radiates from the wall plane, warming the wall mass, the furniture and the people in the room. The film body itself is ultra-thin and flexible, so when it is switched off the room barely notices it is there, and when it is switched on the wall quietly becomes the radiator.

Inside the sheet, printed graphene-carbon resistive stripes run across a laminated film with a silver reflective insulation backing. When current passes through the stripes, they heat up almost instantly; the reflective backing sends the radiated energy back into the room instead of wasting it into the wall behind. The in-line thermostat supplied with the film gives two heat settings, High and Low, so the room can run at economy level overnight and boost up when occupied. Because the element is fully shielded, the film emits no electromagnetic radiation — an important point for bedrooms, nurseries and long office hours.

For B2B buyers, this product is built on the same production platform as SunAura’s wider graphene home heating range. Our Qingdao factory has operated since 2008, runs six automated production lines, holds a monthly output of roughly 500,000 m² of graphene heating film, and ships to more than 50 countries under ISO 9001 quality and ISO 14001 environmental management, with CE and RoHS certification on the product line. Standard wall film is plug-and-play; Standard stock ships as 50 cm-wide strips from 0.3 to 4 m long, on 220 V plug-and-play operation; wider panels are assembled from multiple 50 cm strips. OEM and ODM buyers can discuss cut lengths, plug standards, controller styles and zone-thermostat pairing for their market.

Diagonal close-up of graphene heating film on dark wood surface, silver foil edge
SunAura graphene wall heating film — printed heating stripes behind a silver reflective backing, shown off-wall before installation.

How the Graphene Wall Heater Works

Convection heaters work by warming air, which then rises and circulates. That strategy costs energy: heat collects at ceiling level, rooms feel warm near the heater and cold near the floor, and every door opening dumps a wave of heated air out of the room. A radiant wall film works the other way around. The graphene element reaches operating surface temperature in roughly one minute, as our own demo footage shows, and radiates far-infrared energy toward the opposite wall and the occupants in the room. Those surfaces and bodies absorb the energy and re-emit it slowly, so the room stays evenly warm without drafts, without fan noise and without blowing dust around.

The wall itself acts as a low-temperature storage panel. Once the wall surface is warm, it keeps radiating for a short period even after the film switches off — the kind of gentle thermal mass effect that buyers notice as “warm walls, not just warm air”. For retrofit rooms, rented flats, offices and small hospitality spaces, this is a practical advantage: no radiator occupies floor space, no wet trades are needed, and the heater can sit under a window (where cold downdraft is worst), above a bed, behind a sofa line or over a bathroom vanity wall.

Key Specifications

Parameter Value
Heating element Printed graphene-carbon far-infrared resistive film
Heating principle Far-infrared radiant heating; electric-to-thermal conversion > 99 %
Radiation shielding Fully shielded construction — no electromagnetic radiation emission
Form factor Ultra-thin, flexible sheet; wall-mounted; zero floor space
Backing layer Silver reflective insulation backing (reflects heat into the room)
Supply control Plug-and-play in-line thermostat with two heat settings (High / Low)
Warm-up time Approx. 1 minute to operating surface temperature (product demo footage)
Measured surface temperature Approx. 67.7 °C read by an infrared thermometer gun (factory demo video)
Suitable wall surfaces Interior drywall, plaster, ceramic tile, wood paneling and wallpaper
Mounting method Tape positioning + adhesive fixing; factory-printed fixing-hole strips allow screw fixing
Brand SunAura Thermal
Rated voltage 220 V
Rated power per panel 125–1000 W across the size range (power density 500 W/m²). Per panel: 50×50 cm = 125 W, 50×100 = 250 W, 50×150 = 375 W, 50×200 = 500 W, 50×250 = 625 W, 50×300 = 750 W, 50×400 = 1000 W
Standard panel sizes (W × L) 30×50, 50×50, 50×100, 50×150, 50×200, 50×250, 50×300, 50×400 cm. Standard film width is 50 cm; the 30 cm-wide version is only available on the 30×50 cm panel
Working temperature 45–55 °C (thermostat-controlled)
Typical surface temperature Approx. 60 °C per the factory configuration guide (uncovered surface; varies with ambient conditions)
Surface temperature uniformity ≤ 3 °C across the panel (per factory spec)
Total film thickness Available on request (factory datasheet)
Model / SKU Wall-mounted high-temperature film series (50 cm-wide strips; factory code: graphene electric heating film)
Supply cord length Plug-ready lead with in-line thermostat; exact length on request
Supply notes Standard film width 50 cm; panels wider than 50 cm ship as multiple 50 cm strips (a 1 m-wide order ships as two 0.5 m strips). All panels include the reflective insulation backing; versions without the in-line thermostat ship plug-ready
Installation environment Designed for interior wall installation; not intended for outdoor or wash-down exposure
Certifications CE, RoHS; manufactured under ISO 9001 and ISO 14001 management systems
Warranty (as shown in product demo) Controller 1 year / film body 3 years; backed by SunAura company-level 15-year warranty support for registered B2B partners
Origin & supply Qingdao, China; 6 automated production lines; ~500,000 m² monthly capacity; exported to 50+ countries

Film thickness and exact lead length are published in the factory datasheet on request. Tell us your target plug standard and room sizes, and we will quote the matching strip length and power configuration.

Panel Selection Guide

The film ships as 50 cm-wide strips cut to length. Use this table as a starting point: “indicative main coverage” assumes the wall film is the primary heat source in a reasonably insulated room; “indicative auxiliary coverage” assumes it supplements an existing heater or radiator.

Panel size Rated power (per factory SKU list) Indicative main coverage Indicative auxiliary coverage
30×50 cm 60 W (per factory configuration guide) 0.3–0.5 m² 0.4–0.7 m²
50×50 cm 125 W 0.7–1 m² 0.9–1.2 m²
50×100 cm 250 W 3–5 m² 5–7 m²
50×150 cm 375 W 4–6 m² 6–8 m²
50×200 cm 500 W 5–7 m² 7–9 m²
50×300 cm 750 W 7–10 m² 8–12 m²
50×400 cm 1000 W 10–15 m² 12–16 m²

Coverage figures are indicative — actual results depend on regional ambient temperature and room insulation. Confirm sizing with our engineers before ordering. The 30×50 cm panel is the narrow 30 cm-wide version and is rated 60 W per the factory configuration guide; all 50 cm-wide strips follow the factory SKU list at 500 W/m² density.

Key Features & Benefits

  • Far-infrared radiant comfort — warms walls, furniture and people directly instead of stirring up dust with forced air.
  • Over 99 % electric-to-heat efficiency — nearly every watt drawn becomes radiated heat; nothing is lost to fan motors or chimney-like convection stacks.
  • Zero floor footprint — the film lives on the wall; no radiator, no oil column, no storage heater eating into room layout.
  • About one minute to warmth — fast surface warm-up on the demo bench, with two High/Low settings for boost and economy.
  • Plug-and-play in-line thermostat — standard rooms do not need an electrician; plug into a wall socket and select High or Low.
  • Flexible and corner-friendly — the sheet follows inside corners and uneven walls, with no rigid panel to bend around.
  • Silent and fanless — no blower noise, useful for bedrooms, offices, libraries and hospitality.
  • Shielded, no electromagnetic radiation — safe choice for nurseries, children’s rooms and long office workdays.
  • Simple, documented fixing — tape to position, adhesive to hold, and screw fixing on the printed reinforcing strips if the wall requires it.
  • Smart-thermostat ready — pair the film with SunAura room thermostats for scheduled, zoned control in multi-room projects.

Typical Applications

  • Bedrooms and nurseries — low-temperature radiant warmth above the headboard or across the bed wall; silent, no fan noise at night.
  • Living rooms and lounges — mounted flush below wall art or behind a sofa line; invisible when off, warm when on.
  • Bathroom walls — marble or tiled walls above the toilet give gentle morning warmth without a dedicated heated towel rail circuit.
  • Dining rooms, tea shops and small restaurants — warm walls keep seated customers comfortable while the floor stays clear for chairs and service.
  • Home offices and studies — under a window or behind the desk to chase off under-desk cold during long workdays.
  • Below windows — directly counteracts cold downdraft from glass, the single biggest cold-spot in most rooms.
  • Rental and retrofit projects — no wet trades, no demolition; a weekend upgrade that tenants and landlords both accept.
  • Showrooms, galleries and retail walls — discreet radiant heat that does not compete with the interior design.

Customer Installations — Real Wall-Heating Projects

The photos below are genuine customer and installer shots of SunAura graphene wall heating film, grouped by room type. They show where buyers actually put the film — above headboards, below windows, on marble tile, around inside corners and behind desks — and what problem each installation solves. All images are on walls, indoors, exactly as the product is designed to be used.

Bedrooms & Nurseries

Bedrooms are where buyers feel the difference most: warm walls instead of a noisy fan, and a heater that never reaches for floor space. The film runs along the bed wall above the headboard, giving a soft radiant backdrop across the whole bed.

Graphene heating film above a wooden bed headboard in a bedroom, mosquito swatter on wall
Above a wooden headboard — slim, unobtrusive wall heating that stays clear of bedding.
Wide view of graphene heating film above a wooden bed headboard, bedroom wall
The same headboard install, wider frame — the film reads as a quiet wall trim, not a heater.
Graphene heating film across a bedroom wall above the bed, open door on right
Full-width bed-wall run — one continuous radiant line across the room.
Graphene heating film below a traditional floral wall painting in a bedroom, striped bedding
Below a decorative wall painting — the film sits quietly beneath existing decor instead of fighting it.
Graphene heating film above a pink and blue patterned child's bed, bedroom wall
Above a child’s bed — shielded, silent, low-temperature radiant heat for a nursery.
Graphene heating film under a bedroom window above a red plaid bed
Under a bedroom window — the cold glass downdraft is turned into a warm wall line.

Living Rooms & Lounges

In living rooms buyers care about furniture first: the heater must not steal sofa space or clash with artwork. Installations sit mid-wall below pictures or over damask wallpaper, blending into the interior.

Graphene heating film on living room wall below framed picture, purple floral sofa
Below a framed artwork on a cream wall — invisible when off, warm when on.
Graphene heating film on a high living room wall with recessed lights and beige sofa
High-ceiling lounge — the film complements recessed downlights and modern finishes.
Graphene heating film on beige damask wallpaper above an olive green leather sofa
On damask-pattern wallcovering — the film fixes cleanly over existing wallpaper above a leather sofa.

Dining Rooms, Tea Shops & Small Hospitality

Seated customers feel coldest at their backs. A warm wall behind the dining chairs solves that without taking floor space that service staff need.

Graphene heating film in two tiers on a dining room wall, wooden chairs and table
Two-tier run behind dining chairs — warm back walls, unobstructed floor space.
Graphene heating film on wood-paneled tea shop wall with wooden square stools
Wood-panel tea shop wall — quiet ambiance heating for guests on wooden stools.

Bathroom Walls

The film is intended for interior wall installation; a marble-tiled wall above the toilet is a typical cold-morning spot that buyers choose for gentle radiant warmth.

Graphene heating film on marble-tiled bathroom wall above toilet, pink tag on wall
Above the toilet on marble tile — a warm wall to greet cold mornings.

Home Offices & Studies

Long workdays have two pain points: a cold window behind the shoulders and a cold floor under the desk. The film addresses both as a wall line.

Graphene heating film mounted under a window in a bright home office, white wall, blue sky outside
Directly beneath a large office window — replaces a window radiator without the metal body.
Long graphene heating film strip along a tiled office wall, installation angle view
Full-length run along a tiled wall edge, shown mid-installation beside office furniture.
Graphene heating film low on office wall behind a white desk, wood-look floor
Low behind the desk — keeps feet and under-desk area warm during long hours.

Under-Window Walls and Corners

Below windows and around inside corners are where convection radiators usually struggle. The flexible film follows both.

Graphene heating film under a window with patterned curtains and wallpaper wainscoting
Under a patterned window on a wallpapered wall — defeats cold downdraft in winter.
Graphene heating film wrapping an inside wall corner on wood-look floor
Wrapped around an inside corner — continuous heating without cold spots at the junction.
Graphene heating film on white wall with a green welcome cartoon sticker above
A plain white wall with a playful sticker — proof of how naturally the film blends into everyday decor.

Product Build, Wiring & Installation Detail

These close-ups show what buyers and installers actually receive: the reflective backing, the in-line thermostat, the printed safety strips, and the tape-and-adhesive fixing method used on real walls.

Close-up of graphene heating film silver foil border with printed safety warning strip
Factory-printed safety strip on the reflective foil border — wall-mount, keep front clear, fixing holes may be drilled here, disconnect when unattended.
Diagonal close-up of graphene heating film on dark wood surface, silver foil edge
Diagonal detail — the black heating stripes and silver foil edge on a wood surface.
Close-up of graphene heating film wiring with reflective foil and plug-in thermostat
Wiring detail — silver reflective backing, red/black leads, and the standard plug-and-play thermostat connection.
Graphene heating film corner with red warning label and plug-in thermostat, bedroom
Factory-applied red warning label at the film corner, with the plug-and-play loom.
Close-up of graphene heating film with in-line thermostat control cord, printed safety border
The hand-controlled in-line thermostat hanging from the film — High / Low / Off in one switch.
Graphene heating film held by tape strips during installation, dim room, hand at edge
Installation-in-progress — tape strips hold the film flat while the adhesive cures.
Close-up of graphene heating film taped to wall during installation, dim lighting
Close-up of the tape-fixing technique — the film is pressed flat before permanent fixing.

Video Gallery

Four short clips from our product and installation team: installation method, measured surface temperature, the in-line thermostat and warranty, and the value pitch for buyers worried about winter heating bills. All footage is real — no CGI heaters.

Installation demo & surface-temperature test
Step-by-step wall mounting, followed by an infrared thermometer gun reading about 67.7 °C on the film surface — showing how quickly the graphene film heats once pressed to the wall.
Real operating temperature & finished room
From floor-laid film to a finished panelled living room — demonstrates the actual surface temperature and the comfortable radiant feel buyers report in-use.
Thin profile, thermostat & warranty
Highlights the ultra-thin flexible body, the in-line High/Low/Off switch, and the product-demo warranty of 1 year on the controller and 3 years on the film body; about one minute to heat up.
Value pitch — winter heating bills
A short talk through the buyer’s objection: high winter heating costs, zero floor-space footprint, and the simple plug-in thermostat operation.

Installation Guide

The wall film is designed for DIY-friendly retrofit on ordinary interior walls. Our installers follow the same sequence on every job; the key is to keep the film flat and the front face clear.

  • 1. Prepare the wall. Wipe the wall surface clean and dry. Suitable bases include painted drywall, plaster, ceramic tile, wood paneling and wallpaper. Choose a spot with no furniture blocking the front face — the heat must radiate outward.
  • 2. Position the film. Hold the film against the wall at your chosen height (typically above a headboard, below a window, or behind a sofa line) and secure it temporarily with tape strips along the top and bottom edges, as seen in our installation photos.
  • 3. Fix permanently. Press the film flat onto the adhesive backing so it makes full contact with the wall. If the wall is uneven, plasterboard or high-traffic, use the factory-printed fixing-hole strips along the silver foil border for screws — the print marks exactly where drilling is allowed.
  • 4. Connect the thermostat. Route the power cord to the nearest wall socket. The in-line thermostat with High / Low / Off plugs directly into the socket — no fixed wiring needed for standard rooms.
  • 5. Test and commission. Switch to High, wait about one minute, and check the film is heating evenly across all stripes. Keep the radiating front face unobstructed, then switch to Low for overnight or economy operation.

For fixed-wiring projects, multi-room zoning or commercial hospitality fit-outs, our engineering team can pair the film with SunAura room thermostats and supply a wiring schematic for your electrician.

Safety & Compliance

Safety instructions are printed on the film itself, in both the foil border and the corner warning label, so end users always see them. The rules are simple:

  • Must be wall-mounted. Never run the film on a floor, on bedding, or inside a cabinet.
  • Keep the radiating front face clear. Do not cover the film with cloth, cushions, shelves or stored items.
  • High-temperature surface — never cover. This is a wall-mounted high-temperature film: the uncovered surface typically runs at 50–70 °C and varies with ambient conditions. If the film is covered by clothing, bedding, curtains or any insulating material, the trapped heat can drive the surface temperature above 100 °C rapidly. Never cover the heating surface with any object or insulation.
  • Fixing holes only on the printed strips. Drill where the marking indicates; never drill through a heating stripe.
  • Disconnect when unattended. Unplug or switch off the in-line controller when leaving the room for long periods.

On the compliance side, the wall heating film line carries CE and RoHS certification, and our Qingdao factory operates under ISO 9001 quality and ISO 14001 environmental management systems. The film is shielded so it emits no electromagnetic radiation. For the Japanese market, SunAura sells in compliance with local regulations on a project basis: we discuss certification requirements (including PSE-related matters) per order and confirm the required documentation before shipment, rather than making blanket claims.

Warranty: the in-box product warranty demonstrated in our product video covers the controller for 1 year and the film body for 3 years. Separately, SunAura maintains a company-level 15-year warranty support framework for registered B2B partners, covering manufacturing-defect handling and long-term parts support across our graphene home heating range.

Frequently Asked Questions

How much electricity does the graphene wall heating film actually use?

The film converts more than 99 % of drawn electricity into radiated heat, so there is almost no parasitic loss from fan motors or air circulation. The exact wattage per panel is listed in the specification sheet (pending factory confirmation) and depends on panel size. Because radiant heating warms people and walls rather than just air, rooms typically feel comfortable at a lower air temperature than a convection-heated room. Send us your room dimensions, insulation level and target temperature, and we will estimate the panel configuration and running cost range.

Is the wall heating film safe for bedrooms and children’s rooms?

Yes. The film is fully shielded and emits no electromagnetic radiation; it is silent, fanless and runs at a typical uncovered surface temperature of about 60 °C (measuring about 67.7 °C in our demo footage). It is warm to the touch while uncovered on an open wall, but only because the front face must stay clear — covered by bedding or any insulating material it would overheat, which is why nurseries should use the Low setting on an open wall position. The printed safety rules require wall mounting and a clear front face, and the film carries CE and RoHS certification.

Can I install it myself, or do I need an electrician?

Standard retrofit rooms are plug-and-play: tape the film into position, press it flat, screw the fixing strips if needed, then plug the in-line thermostat into a wall socket. No electrician required. For fixed-wiring, multi-zone or commercial projects, we can supply a schematic for your licensed electrician.

What surface temperature does the film reach?

In our product demo footage, an infrared thermometer gun measured about 67.7 °C on the film surface during testing, and the room-level demo recorded about 50.9 °C in a finished-living-room test. The two High/Low settings let you choose boost or economy. Always keep the front radiating face unobstructed for consistent temperature.

How long does the film last, and what is the warranty?

The product-demo warranty covers the controller for 1 year and the film body for 3 years. Registered B2B partners are additionally covered by SunAura’s company-level 15-year warranty support framework, which handles manufacturing-defect claims and long-term parts supply across our graphene home heating range. Properly wall-mounted and used per the printed safety instructions, the printed graphene element has a long service life — that is the same production platform we have shipped in over 50 countries since 2008.

Which rooms is the wall film best for?

Bedrooms, living rooms, bathroom walls above the toilet, dining rooms and tea shops, home offices, and walls directly below windows — anywhere cold downdraft or under-desk cold is the complaint. It is designed for interior wall installation; it is not intended for outdoor use or wash-down exposure.

Can I cover the film with clothes, a blanket or furniture?

No. The uncovered surface typically runs at 50–70 °C, but if it is covered by clothing, bedding, curtains, cushions or any insulating material, the trapped heat can drive the surface above 100 °C rapidly. This is exactly why the printed safety rules require the radiating front face to stay clear. Keep the full face of the film open to the room, never hang anything on it, and never run it behind bedding or a cabinet.

Can it be paired with a smart thermostat or zoned control?

Yes. The in-line High/Low thermostat is the standard entry solution, but for multi-room projects the film can be paired with SunAura room thermostats for scheduled, zoned, app-controlled heating. Tell us your number of rooms and preferred controller brand, and we will quote the matching setup.

Do you supply the Japanese market, and what about PSE?

SunAura sells compliantly per local regulations. We currently hold CE, RoHS, ISO 9001 and ISO 14001 certification; for the Japanese market we discuss PSE-related documentation on a per-order basis and confirm the required compliance steps before shipment. Send us your project size and we will map the paperwork path.

Related Graphene Heating Products

This wall film is one member of our graphene home heating series. Buyers often pair it with the following: browse the full range in our product center.

B2B PROCUREMENT

Procurement, OEM & Wholesale Terms

Every figure below is the factory specification of this wall film, not a marketing range. If you are specifying for a distributor, a contractor or an OEM programme, this section answers the four questions your purchasing team asks first: compliance, parameters, minimum order and how the price is built.

Compliance

CE · RoHS

ISO 9001 & ISO 14001 factory systems

Minimum order

Flexible

Single panels and trade samples available

Production lead time

25–35 days

Sea freight, after deposit and sample approval

Quotation

Within 24 h

Price, MOQ, freight and lead time in one reply

Technical parameters your specification needs

ParameterValue
Rated voltage220 V (other voltages on request)
Power density500 W/m² across the standard range
Panel output125 W (30×50 cm) up to 1,000 W (50×400 cm)
Working temperature45–55 °C thermostat-controlled; uncovered surface ≈60 °C
Surface uniformity≤3 °C across the panel
Electric-to-thermal conversion>99 %, far-infrared radiant output

See the certification documents — CE, RoHS, ISO 9001, ISO 14001.

MOQ, Incoterms and what we need in order to quote

Samples before volume

Installers and distributors can start with single panels or a mixed trade sample. A sample order is quoted at sample quantity, not at production minimums.

Production MOQ is specification-driven

Minimum quantity depends on film width (standard 50 cm), power density, panel mix and destination. We confirm the exact MOQ in writing with the quotation rather than publishing a number that changes with every configuration.

Incoterms

EXW Qingdao or FOB. Freight, insurance and duty are quoted separately so the unit price stays comparable between suppliers.

Lead time

25–35 days for sea freight after deposit and approved sample; express air for samples and urgent pilot runs.

How the price is built — volume bands

Order stageTypical quantity (guide)What the quotation covers
Sample / evaluation1–5 panels or 1–5 m²Unit sample price, packaging, express freight
Trial order20–100 m²Per-m² or per-panel price, MOQ confirmation, freight options
Wholesale / distributor100–1,000 m²Volume price break, mixed-size pallet loading, private-label packaging
Project & OEM1,000 m²+ or annual programmeProgramme pricing, label/tooling setup, scheduled releases

Prices are quoted per square metre or per panel and depend on film width, power density, panel mix and Incoterm. We do not publish one list price that would be wrong for your configuration: send the band you fall into and the applicable price break comes back in the 24-hour reply.

OEM / ODM — four steps from specification to shipment

01Specification

Send room layout, target voltage and plug standard, panel sizes and annual volume. We return a configuration sheet with wattage per panel and a bill of materials.

02Sample & approval

Pre-production sample with your label artwork and packaging. You approve surface temperature, uniformity and plug type before tooling is committed.

03Pilot run

Small production batch that validates packing, labelling and logistics, with a QC report and photo record.

04Production & shipping

Scheduled releases against the approved sample, per-batch QC, and export documentation including the CE/RoHS declaration, packing list and invoice.

Send a bulk inquiry — reply within 24 hours

Include quantity (m² or number of panels), panel sizes, voltage and plug standard, destination port, and whether you need private-label packaging. Our engineers size the load room by room and return price, MOQ and lead time together.

Request bulk pricingWhatsApp an engineer

Request a Quote for Graphene Wall Heating Film

Tell us your target voltage, plug standard, panel sizes and number of rooms, and our engineering team will come back with configuration, pricing and lead time from Qingdao. OEM and ODM orders welcome.

Request Wholesale Price
WhatsApp an Engineer

    Distributor, Contractor or OEM Buyer?

    Get a tailored bulk quotation with your branding, packaging and delivery schedule — we reply within 24 hours.

    Get a Bulk Quote